Kettler ADIRONDACK 2511 Manuel d'utilisateur télécharger pdf

Made in the U.S.A.

www.kettlerusa.com

[email protected]

Properly Seated

Washer and Nut.

Slide washer then

locknut onto end of

bolt then tighten.

Place arm rest

on top of chair

legs, align front

predrilled holes,

insert bolt.

Attach the

braces to

the legs by

aligning holes

and inserting

a 2” bolt.

Attach the back

of the chair by

aligning holes on

the arm and the

seat to insert bolt.

3b.

3a.

Insert the bolt thru the center

seat brace into the center of the

back of bench.

Assembly Instructions

a. Align predrilled holes then insert bolts

to attach front legs.

1a.

b. Align predrilled

holes then insert bolts

to attach back legs.

1b.

2511 ADIRONDACK BENCH

Contents:

(1) Seat, (1) Back

(2) Arm Rests

(2) Front Chair legs

(2) Back Chair legs

(2) Cross Braces

Tools Required:

#3 Phillips Head Screwdriver

7/16” Wrench

(18) 1/4 - 20 x 2” Bolts

(2) 1/4 - 20 x 2 1/2” Bolts

(1) #10 x 3” Screw

(10) Washers

(10) Locknuts

Locknut Washer Bolt

a. With the wing on the post facing front,

align the predrilled holes on front leg to the seat

and insert the 1/4 - 20 x 2” Bolts through the leg

in thru the seat. Clean any plastic residue from

the bolt then slide a washer on. Screw on the

locknut and then tighten it with the wrench and

phillips screwdriver.

b. Align the predrilled holes on the back leg to

the seat and insert the 1/4 - 20 x 2” Bolts through

the leg in thru the seat. Clean any plastic residue

from the bolt then slide a washer on. Screw on the

locknut and then tighten it with the wrench and

phillips screwdriver.

Repeat on the other front leg.

Place arm rest on top of chair legs align the

front predrilled holes and insert the 1/4 - 20 x 2”

Bolts through the leg and in thru the arm. Clean

off any plastic residue then slide a washer on the

end of bolt. Screw on the locknut and then tighten

it with the wrench and phillips screwdriver.

a. Attach the back of the chair to the seat

by aligning holes and inserting a 1/4 - 20 x 2”

Bolt then tighten with a phillips screwdriver.

b. Attach the back of the chair to the arm by

aligning holes and inserting a 1/4 - 20 x 2” Bolt

thru the arm, leg and into the chair back, then

tighten with a phillips screwdriver.

Repeat on both sides.

Attach the cross braces of the chair to the

legs by aligning holes and inserting a 1/4 - 20 x

2” Bolt through the leg into the cross brace and

tighten with a phillips screwdriver.

Repeat on other leg.

Do Front and Back cross braces.

Attach the center seat brace underneath to

the back, insert a #10 x 3” screw thru the brace

into the center of the bottom back support then

tighten with the screwdriver.

1 2

Résumé du contenu

Page 1 - 2511 ADIRONDACK BENCH

Made in the [email protected] SeatedWasher and Nut.Slide washer then locknut onto end of bolt then tighten.2.Place a

Page 2 - KETTLER Limited Warranty

KETTLER® International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453www.kettlerusa.com • [email protected] & MaintenanceOcean Co

Commentaires sur ces manuels

Pas de commentaire

Kettler ADIRONDACK 2511 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Kettler ADIRONDACK 2511. Kettler ADIRONDACK 2511 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Kettler ADIRONDACK 2511