Kettler 2533 Manuel d'utilisateur télécharger pdf

Place arm rest on top of chair legs, align

front predrilled holes, insert bolt.

2533 ADIRONDACK BAR STOOL

Contents:

(1) Seat, (1) Back

(2) Arm Rests

(2) Front Chair legs

(2) Back Chair legs

(1) Footrest

(2) Side Braces

Tools Required:

7/16” Wrench

(1) Short Cross Brace

(4) Cross Braces

(22) 1/4 - 20 x 2” Bolts

(6) 1/4 - 20 x 2 1/2” Bolts

(12) Washers

(12) Locknuts

a. Align predrilled then

insert bolts to attach

front legs.

b. Align predrilled

holes then insert bolts

to attach back legs.

Locknut Washer 1/4-20 x 2” Bolt

#3 Phillips Head Screwdriver

Properly Seated

Washer and Nut.

Assembly Instructions

a. With the wing on the post facing front,

align the predrilled holes on front leg to the seat

and insert the 1/4 - 20 x 2” Bolts through the leg

in thru the seat. Clean any plastic residue from the

bolt then slide a washer on. Screw on the locknut

and then tighten it with the wrench and phillips

screwdriver. Repeat on the other front leg.

b. Align the predrilled holes on the back leg to

the seat and insert the 1/4 - 20 x 2” Bolts through

the leg in thru the seat. Clean any plastic residue

from the bolt then slide a washer on. Screw on the

locknut and then tighten it with the wrench and

phillips screwdriver. Repeat on the other back leg.

Place arm rest on top of chair legs align the

front predrilled holes and insert the 1/4 - 20 x 2”

Bolts through the leg and in thru the arm. Clean

off any plastic residue then slide a washer on the

end of bolt. Screw on the locknut and then tighten

it with the wrench and phillips screwdriver.

a. Attach the back of the chair to the seat

by aligning holes and inserting a 1/4 - 20 x 2”

Bolt then tighten with a phillips screwdriver.

b. Attach the back of the chair to the arm by

aligning holes and inserting a 1/4 - 20 x 2 1/2”

Bolt thru the arm, leg and into the chair back, then

tighten with a phillips screwdriver.

Repeat on both sides.

Attach the cross braces of the chair to the

legs by aligning holes and inserting a 1/4 - 20 x

2” Bolt through the leg into the cross brace and

tighten with a phillips screwdriver.

Repeat on other leg.

Do Front and Back cross braces.

Slide washer then

locknut onto end of

bolt then tighten.

Attach the braces to

the legs by aligning

holes and inserting

a 2” bolt.

Attach the back of the

chair by aligning holes

on the arm and the seat

to insert bolt.

3b.

3a.

1 2

Résumé du contenu

Page 1 - 2533 ADIRONDACK BAR STOOL

Page 2 - KETTLER Limited Warranty

KETTLER® International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453www.kettlerusa.com • [email protected] & MaintenanceOcean Co

Commentaires sur ces manuels

Pas de commentaire

Kettler 2533 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Kettler 2533. Kettler 2533 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Kettler 2533